Stratek Plastic Ltd

Extensional / Elongational Flow Mixing
 

 

Events


Additives,
Compounding, & Coatings 

March 8 - 10, 2010  Atlanta, Georgia
USA
Hilton Airport Hotel
 


May 16-20, 2010
Orlando World Center
Marriott Resort &
Convention Center
Orlando, Florida USA


June 7 - 10, 2010 
Fispal Food Service
Expo Center North
São Paulo - Brazil




 

 
Home News / Updates
Stratek News/Updates

Welcome To Stratek

E-mail Print PDF
Welcome to Stratek Plastic Ltd.

Tek-MixTM - Extensional / Elongational Flow Mixing
The Next Step in Mixing & Blending
  
Read more...
 
E-mail Print PDF

Found on the Web: Plasticstoday.com

Plastics remained a bright spot for U.S. trade in 2008 

By Tony Deligio
Published: October 21st, 2009

Despite a decline of 23% in the final quarter of the year, U.S. plastic exports increased by 6.7% in 2008 and eclipsed $50 billion for the first time ever, according to the latest international trade statistics for the plastics industry, which are summarized in a new report from the Society of the Plastics Industry (SPI; Washington, DC).

Exports during the fourth quarter of 2008 were off 23% from the prior quarter and 12% from the same quarter in 2007, but for the year, they exceeded $51 billion and accounted for approximately 4.4% of all U.S. exports. An overall trade surplus in plastics was not only maintained but expanded, as imports increased, but by only 3.0%, to just under $39 billion. The overall plastics trade surplus grew by nearly 20% from $10.9 billion in 2007 to $13.0 billion in 2008. Much of that surplus resulted from $18.4 billion in resins and raw material exports.

Read more...
 

Stratek’s Tek-Mix Technology Presentation

E-mail Print PDF
European Conference Provides Warm Reception
Stratek presented its latest test results  featuring Tek-MixTM technology at a conference in Germany recently.  The presentation covered Stratek’s advances in mixing and blending  additives and fillers including carbon nanotubes (CNT’s), nanoclays, and pigments.   One of the main strengths of the Tek-MixTM technology is its ability to exploit the advantages of Elongational Flow for dispersing and distributing particles without causing excessive degradation to the host resins. For additional information on Stratek’s technical abilities, click here.
 

Nylon 6 and 6/6: Key Stratek Materials

E-mail Print PDF

From the Stratek Reading Room...

"The Materials Analyst, Part 98:  A Tour of the World of Nylon-Part 1"
An Article by Michael Sepe, published in Injection Molding Magazine - July 2008

Stratek has done considerable experimentation and material processing involving Polyamides (Nylon).  Therefore this article caught our eye when we found it in the July Issue of Injection Molding Magazine.   We think it addresses both the basics and some more advanced information concerning the differences in the chemistry and structure of these two important materials.

Read more...
 


Newsflash

Found on the Web: Plasticstoday.com

Plastics remained a bright spot for U.S. trade in 2008 

By Tony Deligio
Published: October 21st, 2009

Despite a decline of 23% in the final quarter of the year, U.S. plastic exports increased by 6.7% in 2008 and eclipsed $50 billion for the first time ever, according to the latest international trade statistics for the plastics industry, which are summarized in a new report from the Society of the Plastics Industry (SPI; Washington, DC).

Exports during the fourth quarter of 2008 were off 23% from the prior quarter and 12% from the same quarter in 2007, but for the year, they exceeded $51 billion and accounted for approximately 4.4% of all U.S. exports. An overall trade surplus in plastics was not only maintained but expanded, as imports increased, but by only 3.0%, to just under $39 billion. The overall plastics trade surplus grew by nearly 20% from $10.9 billion in 2007 to $13.0 billion in 2008. Much of that surplus resulted from $18.4 billion in resins and raw material exports.

Read more...